Publications
 

Journal Publications

1. E Du, Souran Manoochehri, "Optimal Design of Microgrooved Channels with Electrokinetic Pumping for Lab-on-a-Chip Applications", IET Nanobiotechnology, submitted, 2010.

2. E Du, Souran Manoochehri, "Microfluidic Pumping Optimization in Microgrooved Channels with AC Electrothermal Actuations", Applied Physics Letters, Vol.96, 034102, 2010.

3. Navin Kumar and S.P.Singh,"Experimental Study on Vibration and Damping of Curved Panel Treated with Constrained Viscoelastic Layer", Composite Structures, In Press, Available online 15 July 2009.

4. Kishore Pochiraju, Gyaneshwar P. Tandon,"Interaction of oxidation and damage in high temperature polymeric matrix composites", Composites Part A: Applied Science and Manufacturing, In Press, Corrected Proof, Available online 1 April 2009.

5. Navin Kumar and S.P.Singh,"Vibration and damping characteristics of beams with active constrained layer treatments under parametric variations", Materials and Design, Volume 30, Issue 10, 2009, Pages 4162-4174.

6. O. Sul, S. Jang and E. H. Yang, "Step-edge calibration of torsional sensitivity for lateral force microscopy", Measurement Science and Technology, 20, 115104, 2009.

7. E Du, Souran Manoochehri, "Enhanced AC Electrothermal Fluidic Pumping in Microgrooved Channels", Journal of Applied Physics 104 (6), art. no. 064902, 2008.

8. E Du, Souran Manoochehri, "Electrohydrodynamic-mediated Dielectrophoretic Separation and Transport Based on Asymmetric Electrode Pairs", Electrophoresis, 29 (24), pp. 5017-5025, 2008.

9. G.P. Tandon, K.V. Pochiraju, G.A. Schoeppner,"Thermo-oxidative behavior of high-temperature PMR-15 resin and composites", Materials Science and Engineering: A, Volume 498, Issues 1-2, 20 December 2008, Pages 150-161.

10. Yunn-Tzu Yu, Kishore Pochiraju,"Modeling long-term degradation due to moisture and oxygen in polymeric matrix composites", Materials Science and Engineering: A, Volume 498, Issues 1-2, 20 December 2008, Pages 162-165.

11. K. H. Ko, K Pochiraju and S. Manoochechri,"An Embedded System for Knowledge-Based Cost Evalutaion of Molded Parts", Journal of Knowledge-Based Systems, Volume 20, March 2007, No. 3, pp 291-299.

12. Yunn-Tzu Yu, K Pochiraju,"Characterization of Temperature Dependent Moisture Diffusivity in PMR-15 Resin", Journal of Polymer Science, 2007.

13. Kwang Hee KO, K Pochiraju and S Manoochehri,"Dynamic Evolution of Information Complexity for Analysis of Design and Development", JSME Journal of Advanced Mechanical Design, Systems and Manufacturing, Volume 1, 2007, No. 1, pp. 36-47.

14. K. Pochiraju and G. Tandon,"Modeling Thermo-Oxidative Layer Growth in High-Temperature Resin", Journal of Engineering Materials and Technology, Volume 128,Jan-2007, Issue 1, pp. 107-116.

15. G. Tandon, K. Pochiraju, G. Schoeppner,"Modeling oxidative development in PMR-15 Resin", Journal of Polymer Degradation and Stability, Volume 91, Issue 8 , August 2006, pp. 1861-1869.

16. K. Pochiraju and V. Jovanovich, "Modeling material property heterogeneity in fiber-reinforced injection molded plastic parts", Journal of Polymer Composites , Volume 26, Issue 1, 2005, pp. 98-113.

17. K. V. Pochiraju and G. P. Tandon, "Extraction of Singular Stress Fields Using the Axisymmetric Single-Fiber Micromechanics Model", International Journal of Fracture , Volume 132, April 2005, pp. 329-349.

18. A. Cheung and K. Pochiraju, "Three-dimensional Finite Element Simulation of Curing of Polymer Composites", Journal of Finite Elements in Analysis and Design , Volume 40., 2004, pp. 895-912.

19. C. Yu and S. Manoochehri, "Optimal Packing Using Multiple Mating Method", Engineering with Computers An International Journal for Simulation-Based Engineering, Vol. 16, June 2003.

20. Y-T. Yu and K. Pochiraju, "Three dimensional Simulation of Moisture Diffusion in Polymer Composite Materials", Journal of Polymer-Plastics Technology and Engineering , Volume 42 (5), 2003, pp. 737-756.

21. C. Yu and S. Manoochehri, "Nesting Arbitrary Shapes Using Geometric Mating", ASME Journal of Computing and Information Science in Engineering, Vol. 2, No. 3, 2002.

22. Kee Park, K. Pochiraju, C.Chassapis, S. Manoochechri, D. Newport, "Knowledge-based rapid design evaluation methodology for die-cast components", Journal of Concurrent Engineering and Research Applications, Volume 10, No.1, 2002, pp.67-74.

23. K. Pochiraju, G. P. Tandon and N. J. Pagano, "Analyses of Single Fiber Pushout Considering Interfacial Friction and Adhesion", Journal of Mechanics and Physics of Solids , Volume (49), 2001, pp. 2307-2338.

24. P.Y. Shim and S. Manoochehri, "A Hybrid Deterministic/Stochastic Optimization Approach for the Shape Configuration Design of Structures",Journal of Structural Optimization, Vol. 17, No. 2/3, April 1999,pp. 113-129.

25. B. Mottahed and S. Manoochehri, "Design Considerations For Electronic Enclosures Utilizing Polymeric Materials", Journal of Polymer-Plastic Technology and Engineering, Vol. 38, No. 5, 1999.

26. K. Pochiraju and T-W. Chou, "Three-Dimensionally woven and braided composites-I: A model for anisotropic stiffness predction",Journal of Polymer Composites, Volume 20, No.4, 1999, pp. 565-580.

27. K. Pochiraju and T-W. Chou, "Three-Dimensionally woven and braided composites-II: An Experimental Characterization,"Journal of Polymer Composites, Volume 20, No.4, 1999, pp. 733-747.

28. L. Q. Tang, K. Pochiraju, C. Chassapis, and S. Manoochehri, "A Computer-Aided Optimization Approach for the Design of Injection Mold Cooling Systems", ASME Journal of Mechanical Design, Vol. 120, June 1998, pp. 165-174.

29. K. Pochiraju, C. Chassapis, and S. Manoochehri, "Multidisciplinary Parametric Design Optimization For Enhancing the Affordability of Molded Composites", Journal of Thermoplastic Composite Materials, Vol 11, July, 1998, pp. 364-392.

30. T.P. Skourlis, S. R. Mehta, C. Chassapis, and S. Manoochehri, "Impact-Fracture Behavior of Injection Molded Long-Glass Reinforced Polypropylene",Journal of Polymer Engineering and Science, Vol. 38, No. 1, Jaunuary 1998, pp. 79-89.

31. P. Y. Shim and S. Manoochehri, "Optimal Configuration Design of Structures Using the Binary Enumeration Technique", Journal of Finite Elements in Analysis and Design, Vol. 31, No. 1, November 1998,pp. 15-32.

32. M. Weinstein and S. Manoochehri, "Identification and Elimination of Parts Undercuts for Molding Applications Through Part Geometry Integration", Journal of Computer-Aided Design.

33. K. Pochiraju, C. Chassapis, and S. Manoochehri, "Parametric Design Optimization of Injection Molded Parts Using a Structured Knowledge-Base",Journal of AI in Engineering Design and Manufacturing.

34. Skourlis, S. R. Mehta, C. Chassapis, and S. Manoochehri, "Impact-Fracture Behavior of Injection Molded Long-Glass Reinforced Polypropylene", Journal of Polymer Engineering and Science, Vol. 38, No. 1, Jan. 98, pp. 79-89.

35. T.P. Skourlis, K. Pochiraju, C. Chassapis, and S. Manoochehri, "Structure-Modulus Relationships for Injection Molded Long Fiber-Reinforced Polyphthalamides", Composites Engineering - Part B, 29 (3), 1998, pp. 309-320.

36. T. Skourlis, B. Mohapatra, C. Chassapis, and S. Manoochehri, "Evaluation of the Effect of Processing Parameters on the Properties of Advanced Styrenic Resins - A Design of Experiments Approach", Journal of Advances in Polymer Technology, Vol. 16, No. 2, 1997, pp. 117-128.

37. B. Mottahed and S. Manoochehri, "Investigation of Composite Materials Selection and Joint Design Layout Design to Enhance EMI Shielding of Electronic Equipment", Journal of Polymer Engineering & Science, Vol. 37, No. 3, March 1997, pp. 653-666.

38. B. Mottahed and S. Manoochehri, "Material and Geometry Factors in Joint Design of Electronic Equipment to Minimize Electromagnetic Interference", Journal of Applied Polymer Science, Vol. 64, no. 9, May 1997, pp. 1667-1679..

39. T.P. Skourlis, C. Chassapis, and S. Manoochehri, "Fiber Orientation Morphological Layers in Injection Molded Long Fiber Reinforced Thermoplastics",Journal of Thermoplastic Composite Materials, Vol. 10, September 1997, pp. 453-475.

40. P. Y. Shim and S. Manoochehri, "Generating Optimal Configurations in Structural Design Using Simulated Annealing", International Journal for Numerical Methods in Engineering, Vol. 40, No. 6, March 1997, pp. 1053-1069.

41. M. Weinstein and S. Manoochehri, "Optimum Parting Line Design of Molded and Cast Parts for Manufacturability",SME Journal of Manufacturing Systems, Vol. 16, No. 1, 1997,pp.1-12.

42. G. Mychajluk, S. Manoochehri, and R. S. Parnas, "Resin Transfer Molding Process Optimization for Minimum Cycle-Time", Journal of Advanced Materials, Vol. 28, No.1, Oct. 1996, pp. 9-18.

43. L. Tang, C. Chassapis, and S. Manoochehri, "Optimal Cooling System Design for Multi-Cavity Injection Molding", Journal of Finite Elements in Analysis and Design, Vol. 26, No. 3, 1997, pp. 229-251.

44. Q. Tang, K. Pochiraju, C. Chassapis, and S. Manoochehri, "Three-Dimensional Transient Mold Cooling Analysis Based on Galerkin Finite Element Formulation with a Matrix-Free Conjugate Gradient Technique", International Journal of Numerical Methods in Engineering, Vol. 39, No. 18, September 1996, pp. 3049-3064.

2010 Conference Presentations

" Hybrid Metal-ceramic Thermo-oxidation Protection Layers for Polymer Matrix Composites "
Kishore Pochiraju, SEM Annual Conference & Exposition on Experimental and Applied Mechanics, Indianapolis, Indiana, USA, June 7 - 10, 2010.

" Color Assisted Iterative Closest Point (ICP) Algorithm "
H. Men, K. Pochiraju, The 2nd International Conference on Computer and Automation Engineering, Singapore, Feb 26-28, 2010.

" Hue Assisted Registration of 3D Point Clouds "
H. Men, K. Pochiraju, ASME 2010 International Design Engineering Conferences & Computers and Information in Engineering Conference, Montreal, Quebec, Canada, August 15-18, 2010.

" Development of a microfluidic mixer for lab-on-a-chip applications with active and passive actuations "
Kasra Manoocheri, E Du, ASME IDETC 2010 conference, Montreal, Quebec, Canada, submitted.

2009 Conference Presentations

" Electrothermal analysis of micro/nanowire initiators for energy production applications "
Seongjin Jang, Sarah Du, Daizong Li, Nelson Pinilla, Biruk A. Gebre, Kishore Pochiraju, and Souran Manoochehri, PowerMEMS-2009 P-065, Silver Spring, MD, Dec, 2009.

" Fabrication of polymeric and polymeric nano-composite MEMS structures "
Daizong Li, Serdar Tumkor, S. Manoochehri & K. Pochiraju, ASME IMECE, Orlando, FL., Nov. 2009

" Determination of Mechanical Properties and Actuation Behaviors of Polypyrrole-Copper Bimorph Nanoactuators "
O. Sul, S. Jang, and Eui-Hyeok Yang, ASME International Mechanical Engineering Congress and Exposition, Lake Buena Vista, Florida, Nov, 2009.

" Remotely Operated and Autonomous Mapping System (ROAMS) "
B.A. Gebre, H. Men, K. Pochiraju, 2009 IEEE International Conference on Technologies for Practical Robot Applications, Woburn, MA, Nov 9-10, 2009.

" Effect of Stacking Sequence on Oxidation Behavior of Polymeric Matrix Composites "
G. Tandon, K. Pochiraju and R. B. HALL, SAMPE Meeting, Closed Sessions (ITAR Restricted) SAMPE Fall Technical Conference | Wichita, Kansas - October 19-22, 2009

" Damage Progression in Oxidative Environments "
Nan An, Andong Xu and K. Pochiraju, American Society for Composites Conference, September, 2009.

" Optimal Design of an Electrothermal Microfluidic Pump "
E Du, Souran Manoochehri, ASME IDETC, San Diego, California, September 02, 2009.

" Characterizing Thermo-oxidative Behavior of Multi-Directional Laminated Composites "
G. P. Tandon, K. V. Pochiraju and R. B. Hall, ICCM-13, Edinburgh, Scotland, July 27-31, 2009.

" Thermal Conductivity of Cracked Gold Nanowires "
Navin Kumar and Kishore Pochiraju, 12th International Conference on Fracture Ottawa, Canada, July 12 - 17, 2009.

" Spectral Analysis of Stress States in Atomistic Single Crystal Models "
Navin Kumar and Kishore Pochiraju, Nanotech Conference and Expo 2009, Houston, TX, May 3-7, 2009.

" Fabrication of vertically standing metal nanowire arrays on silicon substrates using anodized aluminum oxide (AAO) and polycarbonate (PC) membrane, Micro- and Nanotechnology Sensors, Systems, and Applications "
Seongjin Jang, Souran Manoochehri, and Eui-Hyeok Yang, Proceedings of SPIE Volume 7318-57, Orlando, Florida, May, 2009.

" Parameter Estimation of Acoustic Signals Using Linear Microphone Arrays "
Liwen Guo, Biruk Gebre, and Kishore Pochiraju, 2009 Sarnoff Symposium, Princeton, NJ, March 30 - April 1, 2009.

" Scale-Dependent performance of Piezo-Composites "
Nelson Pinilla and Kishore Pochiraju, 138th Annual Meeting and Exhibition, TMS, San Fransisco, CA. Feb 15-19, 2009.

" Environmental Barrier Coatings for High Temperature Polymeric Matrix Composites "(CIE)
Kishore Pochiraju, G.P. Tandon, R.B. Hall, High Temple Conference and Workshop, Napa, CA, Feb 9, 2009.

2008 Conference Presentations

" Microgrooves enhanced AC electrothermal pumping for high conductivity microfluids "
E Du, Souran Manoochehri, 2008 Proceedings of the ASME IDETC, DETC 2008, pp. 831-83.

" Numerical simulation of AC electrothermal microfluidic pumping "
E Du, Souran Manoochehri, 2008 Proceedings of the ASME - 2nd International Conference on Integration and Commercialization of Micro and Nanosystems, MicroNano 2008 , pp. 487-493.

27th High Temple Workshop, Savannah, GA February 2008
Coupled Damage and Oxidation Growth in High Temperature Polymer Matrix Composites, Kishore Pochiraju, G. P. Tandon, G. A. Schoeppner

2nd Integration & Commercialization of Micro & Nanosystems International Conference & Exhibition,
June 3-5, 2008 , E (Sara) Du and S. Manoochehri

2nd Integration & Commercialization of Micro & Nanosystems International Conference & Exhibition.
June 3-5, 2008 , Navin Kumar and K. Pochiraju

2008 ASEE Annual Conference & Exposition
June 22 - 25 - Pittsburgh, PA S. Tumkur and K. Pochiraju

GLOGIFT 08, Eighth Global Conference on Flexible Systems Management Hoboken, NJ, June 14-16, 2008,
Simulation Driven Reconfiguration of High Volume Manufacturing , M. Manzione and K. Pochiraju

ASME International Design Engineering Technical Conferences (IDETC) and
August 3-6, 2008 , Hao Men and K. Pochiraju

ASME International Design Engineering Technical Conferences (IDETC) and Computers and Information in Engineering Conference (CIE)
August 3-6, 2008 , C. Yu, K. Pochiraju, S. Manoochehri

XII International Congress of Theoretical and Applied Mechanics Adelaide, Australia, August 24-30, 2008 Damage Evolution during Thermo-Oxidation of Polymeric Matrix Composites Kishore Pochiraju (USA), Gyaneswar Tandon and Greg Schoeppner

23rd Technical Conference of American Society for Composites,
September 9-11, 2008 Memphis, TN , K. Pochiraju, G. Tandon and G. Schoeppner

4th International Conference on Composites Testing and Model Identification TBD
20 - 22 October 2008

Conference Publications (2006 and Earlier)

1. K. Pochiraju, G. Tandon, and G. Schoeppner,"Thermo-Oxidative Degradation in Polymer Matrix Composites", 25th High Temple Conference and Workshop, Point Clear, Al, February 2005

2. K. H. Ko, C. Yu, K. Pochiraju and S. Manoochehri,"Analysis of information complexity during product development",Proceedings of IDETC/CIE 2005: 2005 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, DETC2005-85284

3. Kishore V. Pochiraju, Gregory Schoeppner, Gyaneswar P. Tandon," Role of Fiber-Matrix Interface on the Thermo-Oxidative Degradation",Proceedings of the 20th American Society For Composites,Philadelphia, PA 19104

4. K. Pochiraju, G. Tandon, and G. Schoeppner,"Time Dependent Composite Behavior under Thermo-Oxidative Environmental Conditions", Proceedings of ASME, IMECE, Anaheim, CA, November 2004

5. Kishore V. Pochiraju, Gregory Schoeppner, Gyaneswar P. Tandon,"Modeling of oxidative development in pmr-15 resin", Proceedings of the SAMPE Conference, Long Beach, CA, March 2004

6. C. Yu, C. McKonly and S. Manoochehri, "Optimal Packaging of Tank Turret System", Proceedings of ASME Design Engineering Technical Conferences and Computers and Information in Engineering Conference, Chicago, Illinois, September 2-6, 2003

7. C. Yu and S. Manoochehri, "Hybrid Approach for Containment Problems", Proceedings of ASME Design Engineering Technical Conferences and Computers and Information in Engineering Conference, Montreal, Canada, September 29-October 2, 2002

8. C. Yu and S. Manoochehri, "Optimal Layout of Irregularly Shaped Objects", Proceedings of ASME Design Engineering Technical Conferences, Baltimore, MD, September 10-13, 2000

9. F. Soltani and S. Manoochehri, "A Geometry-Based Model for Determining the Filling Time in Resin Transfer Molding Process", Accepted for SPE/ANTEC 2000, paper # 362.

10. F. Soltani and S. Manoochehri, "A Rapid Method for Prediction of the Vent Locations in Resin Transfer Molding Process", SPE/ANTEC 2000, paper # 363.

11. F. Soltani and S. Manoochehri, "Prediction of the Weld Lines in Injection Molding Process Using Neural Networks", SPE/ANTEC 2000, paper # 372.

12. Tsu-Wei Chou, "Mechanics of three-dimensional textile structural composites: Performance Modeling", Mechanics of Composite Materials and Structures, Kluwer Academic Press, 1999, pp. 173-181

13. " Approximate Energy Release Rate for Adhesion-friction Cracks at the Bi-Material Interface", Proceedings of the American Society for composites 14th Technical Conference, Dayton, OH, September 1999.

14. "Simulation of Residual Stress and Deformation due to Resin Transfer Molding Process", Proceedings of the American Society for composites 14th Technical Conference, Dayton, OH, September 1999.

15. Esche, S. K., Fidan, I., Chassapis, C. & Manoochehri, S., "Knowledge-Based Part and Process Design for Metal Forging", Proceedings of the SAE'99 International Congress and Exposition, Detroit, Michigan, March 1 - 4, 1999.

16. F. Soltani and S. Manoochehri, "Application of Neural Networks in Process Modeling of Molding Processes", ICCE/6, 1999.

17. F. Soltani and S. Manoochehri, "A Neural Network-Based Prediction of the Weld Lines in Resin Transfer Molded Parts", Proceedings of 1999 ASME Design Engineering Technical Conferences, Las Vegas, Nevada.

18. C. Yu and S. Manoochehri, "Overlap Detection Using Minkowski Sum in Two-Dimensional Layout", Proceedings of 1999 ASME Design Engineering Technical Conferences, Las Vegas, Nevada.

19. S. Manoochehri, C. Chassapis, G. Mychajluk, T. Kiel, and D. Newport, "Knowledge-Based Engineering System (K-BESS) for Metal Processes with Application to the Army's Spare Parts", Defense Manufacturing Conference (DMC), December 1998, New Orleans, Louisiana.

20. Fidan, I., Esche, S. K., Chassapis, C. & Manoochehri, S., "An integrated approach to product and process design in metal forging", Proceedings of the 5th Annual Concurrent Engineering and Integrated Product Design Conference CEIPD'98, East Hanover, New Jersey, September 24, 1998, pp. 28-41.

21. S. Manoochehri, "K-BESS Program - Development of Next Generation Knowledge-Based Engineering Design Tools for Defense Applications", Intelligent Design and Manufacturing Tools For Affordable Military Product Development Conference, Stevens Institute of Technology, October 14-15, 1998, Hoboken, New Jersey.

22. C. Chassapis, and S. Manoochehri, "ACES for Composites Applications in Ammunitions", Proceedings of the Defense Manufacturers Conference '98, November 30 - December 3, 1998, in New Orleans, Louisiana.

23. I. Fidan, S.K. Esche, C. Chassapis and S. Manoochehri, "An integrated approach to product and process design in metal forging", Proceedings of the 5th Annual Concurrent Engineering and Integrated Product Design Conference CEIPD 1998.

24. S. Manoochehri, "Integrated Product and Process Development for Composite Materials", Federal Laboratory Consortium Conference Proceedings, April 15, 1997, East Brunswick, New Jersey.

25. S. Manoochehri and B. Mottahed, "A Knowledge-Based Engineering System for Integrated Mechanical Design of Electronic Equipment", 2nd Annual Lucent Pro/E User Conference Proceedings, May 13, 1997, Holmdel, New Jersey.

26. C. Chassapis, and S. Manoochehri, "An Integrated Product-Process Design Methodology for Resin Transfer Molding Components in Structural Applications", Proceedings of the Defense Manufacturing Conference, December 5-6 1996, Miami Beach, Florida.

27. T. Skourlis, K. Pochiraju, C. Chassapis, and S. Manoochehri, "A Study on Processing-Structure Properties of Long Fiber Reinforced Thermoplastics", Proceedings of the Third International Conference on Composites Engineering, ICCE/3, New Orleans, LA, July 21-26, 1996. pp. 771-773.

28. L. Q. Tang, K. Pochiraju, C. Chassapis, and S. Manoochehri, "Optimal Design of Cooling System for Injection Molding", Proceedings of the SPE ANTEC 1996, Volume I-Processing. , Indianapolis, Indiana, May 1996, pp. 714-718.

29. C. Chassapis, V. Gerdes, S. Manoochehri, G. Mychajluk, D. Newport, D. Ostberg, K. Pochiraju, T. Skourlis, and L. Tang, "An Integrated Design Methodology for Resin Transfer Molding of Structural Composite Parts", Proceedings of the 11th Annual Advanced Composites Conf. & Exposition, Dearborn, Michigan, Nov. 1995. pp. 87-101.

30. S. Manoochehri and C. Chassapis, "Integrated Product and Process Design of Long Fiber Reinforced Injection Molded Components", Proceedings of the Defense Manufacturing Conference, Vol. 2, Dallas, Texas, November, 1995, pp. 103-110.

31. M. Weinstein and S. Manoochehri, "Mold Tool Configuration to Minimize Undercuts", Proceedings of ASME Design Automation Conference, Boston, Mass., September 1995. pp. 149-156.

32. K. Pochiraju, C. Chassapis, and S. Manoochehri, "Integrated Design Optimization of Injection Molded Parts with Fiber Reinforced Thermoplastics", Numerical Methods in Thermal Problems, Volume IX, Part 2, Atlanta, Georgia, July 1995, pp. 1349-1360.

33. D. Webb, V. Gerdes, C. Chassapis and S. Manoochehri, "An Intelligent Mold Shop Database: Centralizing Information to Gain Efficiency and Flexibility", Proceedings of 1995 SPE ANTEC, May 1995, Boston, Mass., pp. 983-987.